Richard L. Proenneke Photo

For most of us, this was our introduction to Dick, and his life. It is one of the only films ever made that shows the process of making a cabin in the wilderness, using only hand tools. It is a real gift.

Dick was a man whose life took him to a lot of places and exposed him to a lot of things, and those things may have been instrumental in helping shape his abilities for life in the wilderness. Born and raised in Iowa, he joined the US Navy and was a Navy carpenter, a rancher, diesel mechanic and heavy equipment operator.

He originally went to Alaska to start a cattle ranch, and wound up commercial salmon fishing and working as a mechanic. He spent the final years of his working career in and around Kodiak Alaska at the naval base there, until a work accident nearly cost him his eyesight. His life in the ranching business probably helped him understand nature and wildlife on an intuitive level, and his life as a carpenter and mechanic probably prepared him with the self-sufficiency needed for the next phase of his life. He retired at age 51 to Twin Lakes, living as a naturalist, nature cinematographer, and scientific observer in the remote Alaska wilderness.

In 1962, Dick made his first trip to Twin Lakes Alaska, part of what is now Lake Clark National Park, and lies 40 miles North of Lake Clark, 100 miles West of Kenai and about 350 miles West of Anchorage. This area is full on bush country, and only accessible by floatplane in summer, ski plane in winter.

He was originally introduced to the Twin Lakes area, by friends he made while working at the Navy Base at Kodiak. A retired Navy Captain and his wife, Spike and Hope Caruthers, who had a cabin there, invited Dick to the area, and loaned him the use of their cabin. Dick in turn loaned the use of a camper he had to the Caruthers in the Kodiak Area.

Dick set out to live in a way similar to Henry David Thoreau, as he had written about in “Walden” as a test of his personal life and values. During July 1967, Dick spent time harvesting logs At Twin Lakes, from a small stand of spruce near Spike’s cabin, and on May 21, 1968, he returned to Twin Lakes to build his own cabin, where he remained for the next 16 months. He may not have known at the time, but that first stay would evolve into where he would live for the next 31 years. It began as a test to see what he was made of, and became his home.

He lived in Twin Lakes, off savings from his retirement, from payments received for meteorological and wildlife research, photography he did for the National Park Service, and from showings of the film footage he shot in and around the area.

In 1999, Dick returned to the States to live with his brother in Southern California, Returning only once for a short visit during the summer of 2000, to dedicate his Cabin to the National Parks Service. The cabin is now maintained in the state Dick left it, as a historical site and museum.

Among the many things Dick was, he was a very talented woodsman and woodworker. The first forty minutes of the largely autobiographical video “Alone in the Wilderness” depict him building his cabin from the spruce logs he felled the year before. The video is also interspersed with shots of him doing the other things that make up his life at Twin Lakes.

Let’s have a look at Dick and the tools he brought with him to Twin Lakes, as he builds his cabin, furnishings and living accessories. For many, this is an excellent opportunity to see a trained carpenter from the old school, go about his work with hand tools, and without drawings. Knowing what he wants to do, seeing it in his minds eye, using his skills and developing the materials available right there at his cabin site.

This video is just a taste of the first movie in a series of three, Alone in the Wilderness. If you navigate to the following links, you can watch excerpts of Alone in the Wilderness, Alaska Silence and Solitude and The Frozen North on YouTube.

Alone in the Wilderness

Alaska Silence and Solitude

The Frozen North

Only the first video, “Alone in the Wilderness” depicts Dick doing any woodworking, but I highly recommend watching all three, or even purchasing the videos from DickProenneke.com. If you are like me, you’ll watch them many times.

One of the first things you’ll notice is that Dick has to prepare the cabin site. He clears the brush and lays down a gravel base that he hauls from the lake. Next, he hauls the logs one by one from where he has them stacked to the cabin site. How does he do it? Look closely, he isn’t just dragging them on the ground. He has logs laying crossways in the trail. Dick fashioned an old school skid road.

Among the tools he brought in to build the cabin as well as for survival was a 36 to 40 inch one man tree saw, with teeth filed for softwoods which were predominant in the area, a metal frame style tree saw, a double bladed axe and a hatchet. He has a splitting maul for firewood as well. There is also a shot of him filing an adze, an adze that he was also shown to use like a light sledgehammer when building sawhorses. He uses a drawknife for debarking, flattening and shaping his logs, poles and rough lumber.

Something worth noting about Dick’s axe. He chokes up on the handle often to shave shape and carve. He relies on it for a lot of tasks. He even uses it while hunting. It is hard to see his axe in any shot when it is not in motion, but if you are used to seeing what a good axe looks like, the area near the blade has been filed down to a thinner profile.

Richard L. Proenneke Photo

I am originally from logging country in the Pacific Northwest. We know that many new axes will chop nearly as well as a sledgehammer. The cutting edge is simply too blunt, and when swung, the axe bounces off the tree better than it cuts. You would think it dull, but no. Its cutting edge is just too blunt, and the axe can’t penetrate into the wood fibers to cut cross grain.

What was often done to a new axe by their new owners, was to file or grind that area just behind the edge down some and use a shallower bevel angle on the edge. If you relieve this shoulder a bit, the axe will cut into the wood and not bounce off the wood as you chop. It also makes the blade a lot more versatile as we can see from Dick’s skill with it. This is physical work. Dick knew he needed his tools to work for and with him.

It appears he has at least four handsaws. One is a ripsaw, which he used to resaw logs into planks. He claimed he could rip a log 5 inches in diameter by 42 inches long in 15 minutes. That is not a bad pace when you have a lot of ripping to do, so it was likely in the 4-6 ppi range. There is a shot of it leaning against the planks he had cut. It looked like a 26” Disston D-8.

Dick commonly used both hands on his saw when it was stable to do so, but I couldn’t see a thumbhole on this saw. In the places we see dick cross cut, the saw looks like a D-8 also, but it doesn’t look discernibly different than the crosscut while viewing on the fly. If I am wrong about two D8’s then Dick is using his Rip Saw for some of his crosscuts, and this is doable. He likely dressed most all his sawn edges with his planes anyway.

There was a short cross cut saw, a short panel saw, with no back that looked to be approximately12 inches long, and with what looks like an aluminum handle, as a well as a keyhole saw, used to saw the elaborate latch and lock he made for his Dutch door. It was also likely used to saw out the crescent on the outhouse door as well as make the wooden spoons he carved.

His edge tools appear to include at least a framing slick and gouge, a, block plane and a number 4 Stanley smoother He made many of the handles for tools that needed them from spruce on site, such as the handles for his framing chisels. He likely had more chisels and gouges than just one of each in his kit; likely some of the bench chisel style variety.

There was also what was called a “thin bladed wide chisel” he was shown using to split logs to make boards from for framing windows and doors. It did not appear to have a wooden handle. He struck it with his claw hammer. Something similar to this chisel was seen fitted later with a long wooden handle for chiseling holes in the lake ice for fresh water during the freeze. He had what looked like a wide-bladed, small cold chisel like chisel, likely a brick set, which he used to tack Oakum Moss between the logs while insulating the cabin

His sharpening tools appear to include files, which while not shown would have to include saw files, perhaps a Lansky puck of Carborundum, which he used on his axe, hatchet and drawknife, and likely some other Carborundum stones, which were popular for sharpening in that era.

His drilling tools appear to include a brace, but all we ever see is the collet of that brace while he is drilling handles he made on site for his large augers. It is likely he has a number of bits for his brace, and the large augers we see him use in the timber framing, He likely made the handles for his large augers for a couple reasons. In addition to the leverage he gains, they negate the need for additional braces with different sweeps.

Richard L. Proenneke Photo

His striking tools appear to include a large framing claw hammer, a smaller claw hammer in the 16 ounce range that he used to tack the tarpaper and visqueen on his roof. He made a large wooden mallet carved from spruce. There is also a Crowbar available to him up there, often used for un-boarding boarded up windows for weatherization in winter.

Layout tools include a one-foot combination square, a folding ruler, a tape measure, a chalk line, what was likely a 24 inch level, a pair of dividers and carpenter pencils.

Dick made wooden hinges sawn from seasoned spruce stumps, and made dowel like pins for various joinery needs. He applied glue with a brush in some of these joinery applications. It is hard to say which glues, but they were used outdoors as well as in. In other cases he fashioned round mortises, where a tapered pin went into a hole, much like what was used traditionally in Windsor chairs, but I never saw any tooling that would taper a hole. My guess is that Dick shaved the pins with a drawknife and or whittled them so there would be a friction fit.

Richard L. Proenneke Photo

He made many accessories for living from tin gas cans, so there was likely a pair of tin snips or two but we never see them. There was at least one pair of vise grips and perhaps a pair of pliers. He made baking pans for his beloved sourdough, the starter that he got from Mary Alsworth, Babe Alsworth, his friend and bush pilot’s wife. He made wash basins, other tools for the kitchen. Carrying pans, tin totes and trays, for packing sand, gravel, cement mortar and stones. He made a pail with bail for carrying water from the lake, and covered storage for dry goods.

Dick even made hinges for various doors from these tin cans and nails. From the looks of other metal work for the stove and pipes, as well as flashing and 55 gallon drum usage, he likely had a hacksaw as well. For those without a cutting torch, a cold chisel will take the top off a 55-gallon drum too.

There was also a round point shovel, which he used for gardening and cutting moss for his roof. A hoe he used for mixing mortar for his fireplace and a pointing trowel for cementing the rockwork on the fireplace.

Amongst the tools Dick made were saw horses, a planing horse, which like a Japanese planing beam, had a stop on one end he could plane against. He made a number of different ladders. The spruce mallet, the handles for his augers and framing chisel and gouge. There was also the pack frame for carrying his moss for the roof, which I suspect may have later became the lid to his underground root cellar.

He also made jigs to help make things. The frame he built around the tin box he used to carry mortar and rocks. He made support forms for his rock fireplace chimney and a support form for building its arch. The snow shovel was cut from a 55-gallon barrel, and the bottom of a 55-gallon barrel was used for his cement mixer. He had a shop storage area adjacent to the outhouse where he kept dry wood and his tooling as well.

He made his furnishings. A bunk bed, dining/writing table, chair(s) and benches. He had seating inside and out. He made a couple tables and a carved a bowl from a burl he sawed off a tree. A wall mounted paper towel holder, cabinet next to his bed, various shelves for his dishes, utensils and cooking spices. A kitchen counter appears to have been made from 3-4 planks. He hung his cast iron frying pans on the wall or stored them in an animal proof cache he built outdoors. Even had the use of a cutting board, but did he bring that in? He likely made his snowshoes.

Unfortunately the videos never show all the tools he was seen to use all at once. The logistics of doing this, even as minimally as it was, was something that required a lot of thought and planning. Dick clearly had done his thinking and knew what was needed to use with what was at hand in the Alaska bush country. He had a good friend in Babe Alsworth, helping to fly in the things he needed. Dick was a resourceful man who knew his way around tools and how to use them productively to get what he needed made under a very tight schedule. The Alaskan spring, summer and fall passes by in a very short five months.

What is a self-sufficient craftsman? Fine craftsmanship does not have to be French polish. Is what Dick made rustic? Sure, but it is as durable as the land and stood the test of daily use over 30 years in unforgiving country. If you were wondering what tooling you really must have in your kit, if there is to be nothing other than human power, now you have a good idea.

Richard L. Proenneke Photo

Know that even though there is power from gas and electricity, these tools and skills can still be of great help to us. If you were wondering what skills you need to develop to use them, this too is a good overview. If you need help learning to use tools, and gaining knowledge for building with them, there are many, many titles in the Woodworks Library, which will help address this. Please feel free to go in and have a look around. If you have further questions about these tools and skills, you can also contact me.

If you are interested in some of this tooling, there are some links to many great new and used tool vendors on my Woodworks Tool Source Links page. For some of the specialized timber framing tools, two vendors come to mind. Caribou Blades is a maker of many fine tools for building and surviving in Bush country, and they are truely bush tools, made off grid in the remote bush country of British Columbia, Canada. Scott and Aki have been living this way since 1997. They have been doing “green” since before it became cool. Their tooling is primarily made in the same way Dick made things, from recovered steel, and local woods. Probably the greenest way to go if that appeals to you, and you support people who like Dick did, are living a simplified life, off the grid in a green way. Alternatively, Barr Quarton of Barr Tools also forges up a fine line of timber framing and woodworking tools in Northern Idaho. Both are highly recommended.

The three documentaries about Dick Proenneke and his life are available for purchase from Bob Swerer, the producer of the videos at www.dickproenneke.com They are all wonderfully produced, well narrated and well worth a watch. There are two books, “One Man’s Wilderness”, which is available from Amazon, and “More readings from One Man’s Wilderness”, that is either available from Amazon, or as a pdf download from the National Park Service, Here.

I understand there may be a third book in production from Dick’s journals that will fill the gap between the One Man’s Wilderness of 1968-69 and 1974-1980 where “More Readings” takes over.

Finally for video to go out on, there is a 15-minute clip that depicts Dick in his twilight, in 2000 when he returned to Twin Lakes to dedicate his homestead to the National Park Service.

I hope you enjoy these videos and woodworking insights from Dick, to the world.

“Too many men work on parts of things. Doing a job to completion satisfies me”.
Dick Proenneke

Happy Woodworking!

But actually, I was going to touch on some thoughts and problem solving on the left side of the blade. Table saw that is. It really is the unaddressed side of the machine.

I am a hand tool user, and advocate. Heck, I even make hand tools, but I am also a blended woodworker. For those unfamiliar with the term, a “Blended Woodworker” is a woodworker who espouses both the finesse of hand tools, and the production of power tools and shop machines.

I make no bones about it, as each of us should follow the woodworking path that makes us feel content. Whether you are a power tool woodworker, a blended, woodworker, a hand tool woodworker, and even perhaps a collector, it’s all woodworking and that is a good thing! Whichever way you are doing it, your doing it right for you. That is all that matters.

Many with table saws are faced with various challenges. Cut quality and safe practices are always ones that weigh heavily on the mind, maybe even the left-brain. Those who have the space and desire, enjoy a large cabinet saw with a 60 inch fence set up, maybe an outfeed table that will accommodate full sheets of plywood. The rest of us may not need a saw that takes that much space, and so we opt for saws with a 30 inch fence system, or maybe even less.

There is nothing inherently wrong, but there are unique challenges here. The left side of the blade is the off cut side, and because of the limited width to the right of the blade, sometime the width of what crosses the table saw must ride on the left, even when it is rather largish.

Rather largish presents an overhang to the saw table. This overhang is a fun little exercise, one that has had me wishing I had a few extra arms at times. You know, there you are, you, and the saw blade.

The Zen moment is where there is nothing but you the saw and the cut in the whole world. The largish overhang is gaining it’s ability to counterbalance itself on the left edge of the saw with each inch you cut, and as friction from the table overcomes the weight of the oafish off cut, the inability to keep the big beasty under control with just one hand, has you wishing one eye could continue to watch the fence as the other eye watches near to the blade so you can direct the left arm to do the right thing in independence.

Good times!

NOT.

I work alone and there is no one to ask for help. Even if I had help, the helper needs to know the drill really well, because the ramifications have a direct line to the saw blade. Unwanted effects can be immediate. Suffice it to say, I think working alone is better for me, so I thought about work-arounds for a long time.

In some cases, depending on the length to width ratios, a circular saw with or without a guide is a good way to break down the lumber to sizes you can better finish on the table saw. In this case I didn’t have this ratio problem where the length P is many times the width, whereas the width would not be enough to properly register to the fence of the table saw and counterbalance the length component of the board.

I also needed more speed, better production, and the table saw has that, so I had to figure the best ways to deal with supporting my overhangs. Roller stands seemed like a viable answer, and turn out to be both in part, a piece of the problem and the solution to that problem, but by themselves, they are not the be all end all at the left side of the saw.

The inherent problem with roller stands at the left, is that depending on the width of the material you are cutting, the overhang will likely have to transit from one roller stand to another as the cut is pushed forwards through the saw, and as this happens, the problem of perfect coplanarity is hard to achieve with multiple roller stands that are set to support in the rolling direction. What you get is slight bumps transmitted back to the blade and too, it is not the best thing for your Zen moment. So stand good, roller bad.

After staring at the table saw for a while with the sheet of plywood up on it, I came upon, wait for it– a temporary-roller stand-modifier-jig. I call it the roller stand ski. Well yeah, and it isn’t originally anyone’s idea I’m sure, and heck it’s 2009, branding everything is in, so I have to name it something.

I use those workforce roller stands from the big box stores. They are priced right, fold, hang out of the way, set up quickly, are bearing rollers, have slight tilt adjustments, and for me, owning four of them has been about right. I have used them at every shop machine. They come in lots of variations, but these seemed just right in the pocket for me, cost/benefit wise.

The ski has to mount above the rollers with the stands turned perpendicular to the direction of the cut. I wanted it to work in such a way that I set the stands about where I want them, and for the ski to simply clamp to the stand. When not needed, It is quickly broken down, and the stands hang back up, the ski leans in the corner…

How I made my ski, was sort of a happenstance that came from salvage. A few years back I had planned to use some birch 1×2 with a 1/4 inch chamfer on one corner and a 1/4 inch rabbet on the other as a molding, but no matter how I approached the milling, it tore out. So I rejected it and used a different wood and these boards leaned against the pile causing me to ponder their future going forward. Can’t throw even the failures away, because they still could redeem themselves, somehow. (Yes I do have a selection of smallish off cuts, and I surprisingly use many, but I toss all my sawdust. Honest! )

So I took a six-foot length of this molding I had made and trimmed the ends to make them smooth. Then I drilled three 1/4 inch holes in each end. The first hole on each end is at seven inches in, because this equals the half width of the roller on the roller stand, and each additional hole moving toward the center of the rail was on six-inch centers. All were drilled 5/8ths on an inch in from the side of the 1×2 that has the rabbet. Then the holes were milled with an 82-degree countersink for use with a 1/4-20 flat head cap screw.

When mounted, the chamfered edge on this rail is at such an angle that just the knife-edge of the chamfer supports the wood and with finish and a wax, it offers very little resistance to what is being slid over it. So in one way, this cast off molding had redeemed itself. But wait, there’s more!

For the bracket, as configured, the Workforce roller stand has a 3/8’s inch difference between the roller and the roller bracket, so I used 1/2 Baltic Birch as a shim. It was close enough width wise, and from the scrap bin. I used the molding for the bracket as well, so since the width of the molding is 1-1/2 inches, and the place on the roller stand where the bracket is clamped is also, this shim is square.

The shim is then glued and doweled to a length of molding cut to 4-5/8ths inches long. This will be the clamp end. On the other end I glued and doweled a 1-1/2 inch square piece of the molding, but I staggered it off center a little so that the chamfer o n the square block meets the end grain of the 4-5/8ths piece, this way the chamfer sits a little proud. The benefit to this is that the inside square formed by the rabbet on the opposite side rests against the roller, and this offers support. Funny how this failed molding worked out this way…

I then drilled the bracket on centerline, and again 5/8ths of an inch up from the rabbet side, with a #7 drill bit and tapped the bracket with 1/4-20 machine threads. So the brackets just bolt on, from the rail through to the wood bracket and I tighten to when it reaches a friction fit that still allows rotation of the brackets without needing tools.

The finish is Watco Teak Oil and Wax. That is a moisture resistant finish, which is common on boats and great for the shop. The rail clamps onto a pair of roller stands with a pair of Irwin quick grip ratchet clamps, but any clamp that can offer better pressure than a spring clamp would do. It is easy to adjust, just as you would the roller stands normally, but now you are adjusting an entire plane with two points.

The roller stand ski sure has added a lot of safety and production to the left side of the blade for me, and I even found use for some scraps that didn’t work out. Best thing is that it stows in almost no space at all. The next best thing is, that since the roller stands adjust, I can always set it higher to compensate for the thickness of my table saw sled when crosscutting long boards. Hopefully something like this can help others with a similar conundrum. It is nice to have this kind of help when you work alone.

Happy Woodworking!