Print This Post Print This Post

Dec 29 2017

Woodworking Tool Talk

It’s always fun to talk tools, Right? So I thought it would be a good time to talk about a few of the tools we offer here at Evenfall Studios.

We are best known for our shooting boards, and for nine years now we have been making them for woodworkers all over the world. Every single shooting board is made by one guy in his shop, hands, eyes, careful measurements, and stubborn meticulousness.

We started with the shooting board that is now known as the Deluxe Shooter, and we have expanded on that to include shooting boards that shoot with a single or double chute, from the left hand or right, with a single or double chute.

We have built in the capability to accurately shoot from two to eight angles on our single chute shooting boards, and from three to five different angles on our double chute boards.

We have also included shooting boards that allow you to do everything from the usual lengths and widths in our standard size shooting boards, and have included the ability to easily shoot wide boards at most of the commonly used angles, and long grain as well as super wide boards, so that you can perfect your projects in veneering, lutherie and large casework.

The coolest thing about our shooting boards, we think, is that you can calibrate them to complete and total accuracy every day of the year, no matter where you are. A tool that can overcome wood movement, and provide you with the angles you exactly need. And with flexibility, you are not locked into any specific angle at all, there is even room to calibrate off angle if that’s what you need. In other words, our shooting boards will give you, accurately, any angle you need. All you have to do is calibrate.

Our accessories allow you to shoot both thick and thin boards. We have a fence that you can set with a clamp, which will allow you to shoot any angle between zero and roughly 90° with all of the accuracy possible. We even offer a planing stop for our shooting boards that will allow you to easily plane down to the 1/4 inch thickness, and by laying a piece of 1/8th masonite under your work, in front of the planing stop, you can easily play into the 1/8 inch thickness range.

We offer adapters for every board that we make that will allow you to use any of our shooting boards as a “chute” board, that allows you to enclose a hand plane in a track, for greater ease of use, and perhaps even higher accuracy. Most any shooting board plane, as well as the low angle bench planes can take advantage of this.

Without chute adapters installed, our shooting boards will accommodate any bench plane, any make or model from a number one through a number eight, most block planes, most any wooden plane that was built with parallel sides that are square to the sole. We even offer shooting boards for use with Kanna. So if your desire is to work with Japanese tools, you can have a shooting board for that.

Why do we make so many different kinds of shooting board? Because people work wood so many different ways. We’ve figured out that we could give you the options and all of the accuracy that you’ll need, and so we did. You would be surprised, woodworkers choose to buy every model that we offer, because of the way they work wood. The only way to figure out which one is the best, is to think about which options for you. Beyond that, all our shooting boards will give you all of the accuracy you will need, at every angle they will shoot.

It wasn’t lost on us, that you might need to have a fixture to help you saw. The common miter box isn’t quite as ergonomic as we would like, particularly when we are cutting all of these uncommon angles. We offer a fixture that will help you solve these angles, and do it without having to become a contortionist. If you’re hesitant that you cannot keep your saw square or straight to the work, we also build magnetic side guides that are fully adjustable to any angle that will help keep your aim true.

We realize that shooting end grain and such can help dull a blade. Rather than force you back to your sharpening gear every few minutes to retune the edge, we offer a number of different stropping systems that do have the ability to reach into the dullness and sharpen it back up, without having to do a major grind on your blades. This saves you a ton of time and keeps you woodworking when what you really want to do is build your project instead of sharpening your tools.

The key to keeping your tools sharp is to sharpen them frequently and sharpen them often. This does not mean that you go grab your coarsest stone and go to work rebuilding the edge every time. This means stropping with honing compounds while you are woodworking. We have tools in our shop that haven’t seen an abrasive in more than a couple of years. There has been no damage, we just keep them stropped and working.

Of course you can spend hundreds of dollars on the finest water stones if that’s what you prefer to have, but are sharpening stations can accommodate sandpaper sharpening, you know, the good old scary sharp system. Only the thing is, the advisement that’s out there on the Internet that claim you’ll spend a lot of money on sandpaper isn’t exactly correct when you spend more of your time stropping. The whole trick is to try not to let your tools get so dull that you need to use course abrasives to repair the damage.

Yet, you use a lot less sandpaper that way. But when it comes to needing any abrasives that you could possibly need, Sand paper actually does cover all of the bases and then some. Every knife in the world is made on a belt sander. Every abrasive you could ever want to have is available in sandpaper, and if you’re a diligent stropper, it will be rare that you need to touch up very often. Sharper tools just work better, and your own experience with sharp tools will tell you when it’s time to strop.

Another advantage of course, is not having to completely disassemble your irons from the chip breakers, because stropping is a dry system, and so no moisture is present. It simply means that you pop the blade Assembly out of the plane, strop it, put it back and take a test shaving and you’re back in business. It keeps you sharp in just a couple of minutes. With a chisel there’s nothing to disassemble, you simply take it out of the cut, strop it, wipe it off, and return it to work.

We also wanted to remind you that we have lots of other goodies here on the website. We have the woodwork’s library, filled with over 200 books about woodworking and other trade crafts that are related. We have a full reference section, and we have a great deal of woodworking information right here in all of our indexed blog articles that will help keep you going, if there’s any kind of how to that you need to figure out in woodworking.

We feel that we offer tools that can help take your woodworking from good to great. We hope that you perceive them as being of great value and versatility to your work. They are all about where the rubber meets the road, and making your woodworking projects with all the precision possible.

If you would like to browse at all of the different tools in our store, just scroll to the top of this page and click on the button called store. If you’d like to place an order, our online store is open 24 seven, and if you would rather discuss your order with us via the phone, we can arrange to help you make that call, and we have recently added the ability to allow you to place your order over the phone with us if that is what you would prefer. Yes! you can phone it in if you wanna! Just contact us via email and let us know you’d like to do that and we will set it up! We look forward to hearing from you! Oh, and just in case you were wondering, we are happy to ship internationally via the postal services.

We wanted to say thank you for your business. We are going into our 10th year here, and as a small business that focuses on building tools for woodworkers, we couldn’t have done it without you. We hope that those of you have who have not had the chance to become our clients will consider it. It is our goal to help woodworkers everywhere, building things better. We realize that Shooting boards aren’t the easiest thing in the world to make accurately, but we’ve got that down and we can make you a nice one that we feel is the most accurate and versatile shooting board available. We can also help keep your saws sawing straight, and your edge tools sharp.

If your layout is accurate, and you’re cutting on the waste side of the line, we can help get you the rest of the way to the line with all of the accuracy you need. A shooting board Will make you look good!

Please Follow our Blog! We offer both RSS and email feeds at the top of every blog page!

Recieve our Newsletter! Get tool news and updates first. Subscribe from any page!

For much more frequent woodworking thought from us, please follow our Twitter Feed:


Did you know we are also on Instagram? Please follow us!

We enjoy your questions, comments, ideas and suggestions! Please Contact Us.

Thanks for visiting Evenfall Studios!

© Copyright 2017 by Rob Hanson for evenfallstudios.com All Rights Reserved.

Comments Off on Woodworking Tool Talk